Induction-dynamics ID1.15 Manual de usuario Pagina 12
- Pagina / 20
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
12
Audio Perfection Realized ™
ID1.15 Main Speaker Connection
Remove the jumpers from the binding posts on the back of the ID1.15 and set the switch to
“Three-way + Subwoofer”. Connect the left and right amplifier channels to the top binding
posts on the ID1.15 using normal polarity (red to red and black to black).
Subwoofer Amplifier Interconnect
The ID1.15 is designed to be used with the A2 subwoofer amplifier (designed and built by
Induction Dynamics). The A2 subwoofer amplifier is designed to integrate with audio/video
pre-amplifiers and receivers that have their own built-in low-frequency crossover circuits,
typically containing optional crossover frequency settings. If the crossover frequency is
selectable, the recommended setting for the ID1.15 is 80 Hz with the subwoofer connected
in reverse polarity (see below under Subwoofer Connection).
Using high quality interconnect cables with RCA type terminations, connect “SUBWOOFER
OUT” on the audio/video pre-amplifier or receiver to “IN” on the A2.
You may adjust the subwoofer level using the control in the menu of the audio/video pre-
amplifier or receiver.
Subwoofer Connection
The jumpers should be removed and the switch set to “Three-way + Subwoofer”. Connect
the lower binding posts on the back of the ID1.15 to the A2 subwoofer amplifier in series
using reverse polarity (red to black and black to red).
On the opposite page are diagrams showing alternative methods of connecting the
subwoofers, to achieve the in-series, reverse-polarity connections.
Power Connection
Connect the A2 amplifier to a 120 volt, single phase, 60 Hz, grounded power supply using the
power cord provided. For best results, use a dedicated power circuit for your amplification
equipment.
- Table of Contents 3
- Introduction 4
- General Information 5
- Amplifier Location 6
- Carpet Spikes 6
- Speaker Wire 6
- Speaker Information 7
- Wide Angle™ Phase Alignment 8
- Subwoofer Design 9
- Dual Loudspeaker Switch 9
- Two-Channel (Stereo) 10
- Installation 10
- Multi-Channel (Home 11
- Theater) Installation 11
- Subwoofer Connection 12
- Power Connection 12
- Method #1 13
- Method #2 13
- Method #3 13
- ID1.15 Specifications 14
- A2 Specifications 15
- Warranty 16
- Contacts 17
- Audio Perfection Realized ™ 18
- Overland Park, KS 66210 20
- Tel: (855) 663-5600 20
- Fax: (913) 663-3200 20
Relacionado con productos y manuales para Acústica Induction-dynamics ID1.15
Acústica Induction-dynamics S1 Manual de usuario
(14 paginas)
(14 paginas)
Acústica Induction-dynamics S1.iw Manual de usuario
(19 paginas)
(19 paginas)
Acústica Induction-dynamics S1.8 Manual de usuario
(14 paginas)
(14 paginas)
Acústica Induction-dynamics S1.8ST Manual de usuario
(14 paginas)
(14 paginas)
Acústica Induction-dynamics S2.c Manual de usuario
(14 paginas)
(14 paginas)
Acústica Induction-dynamics C1 Manual de usuario
(12 paginas)
(12 paginas)
Acústica Induction-dynamics C1.8 Manual de usuario
(13 paginas)
(13 paginas)
Acústica Induction-dynamics C2 Manual de usuario
(13 paginas)
(13 paginas)
Acústica Induction-dynamics SW1 Manual de usuario
(18 paginas)
(18 paginas)
Philips RQ1075/22 podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Golarki męskie Philips RQ1075/22.
Dostarczamy 1 pdf podręczników Philips RQ1075/22 do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Comentarios a estos manuales